Is this a crack on the carbon frame?
I have just noticed this on the top of my saddle bar and where the seat post clamp is. Is it a crack probably caused by the saddle pressure?
carbon
asked 4 hours ago
AmirAmir
1204
add a comment |
I have just noticed this on the top of my saddle bar and where the seat post clamp is. Is it a crack probably caused by the saddle pressure?
carbon
asked 4 hours ago
AmirAmir
1204
Take this same photo monthly, and compare it over time. If the line changes and grows in width or thickness then its a crack. If not, it isn't.
– Criggie♦
2 hours ago
add a comment |
I have just noticed this on the top of my saddle bar and where the seat post clamp is. Is it a crack probably caused by the saddle pressure?
carbon
asked 4 hours ago
AmirAmir
1204
I have just noticed this on the top of my saddle bar and where the seat post clamp is. Is it a crack probably caused by the saddle pressure?
carbon
carbon
asked 4 hours ago
AmirAmir
1204
asked 4 hours ago
AmirAmir
1204
edited 4 hours ago
Amir
asked 4 hours ago
AmirAmir
1204
asked 4 hours ago
AmirAmir
1204
asked 4 hours ago
AmirAmir
1204
1204
Take this same photo monthly, and compare it over time. If the line changes and grows in width or thickness then its a crack. If not, it isn't.
– Criggie♦
2 hours ago
add a comment |
Take this same photo monthly, and compare it over time. If the line changes and grows in width or thickness then its a crack. If not, it isn't.
– Criggie♦
2 hours ago
Take this same photo monthly, and compare it over time. If the line changes and grows in width or thickness then its a crack. If not, it isn't.
– Criggie♦
2 hours ago
Take this same photo monthly, and compare it over time. If the line changes and grows in width or thickness then its a crack. If not, it isn't.
– Criggie♦
2 hours ago
add a comment |
1 Answer
1
active
oldest
votes
Doesn’t look like a crack, looks more like a surface void that formed during the resin injection molding. These types of imperfections are not uncommon, especially on the inside of the frame where you can’t see them. Less common to see them on the outside as they are usually caught in quality control inspections. While they are not ideal, as areas with voids will be somewhat weaker than areas without voids (depending on the size and depth of the void), they are not critical like a crack.
answered 4 hours ago
Rider_XRider_X
24.9k14595
1
Most importantly, the irregularity seen in the image has mostly smooth edges (except where worn/machined for the clamp). A crack will generally have sharp edges. However, that very thin line below the more obvious dent could be a crack. But it's more likely just a less severe indication of the mold seam that created the dents at the top. A closer examination would be needed to see if its edge are rounded or sharp.
– Daniel R Hicks
3 hours ago
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "126"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fbicycles.stackexchange.com%2fquestions%2f60186%2fis-this-a-crack-on-the-carbon-frame%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
Doesn’t look like a crack, looks more like a surface void that formed during the resin injection molding. These types of imperfections are not uncommon, especially on the inside of the frame where you can’t see them. Less common to see them on the outside as they are usually caught in quality control inspections. While they are not ideal, as areas with voids will be somewhat weaker than areas without voids (depending on the size and depth of the void), they are not critical like a crack.
answered 4 hours ago
Rider_XRider_X
24.9k14595
1
Most importantly, the irregularity seen in the image has mostly smooth edges (except where worn/machined for the clamp). A crack will generally have sharp edges. However, that very thin line below the more obvious dent could be a crack. But it's more likely just a less severe indication of the mold seam that created the dents at the top. A closer examination would be needed to see if its edge are rounded or sharp.
– Daniel R Hicks
3 hours ago
add a comment |
Doesn’t look like a crack, looks more like a surface void that formed during the resin injection molding. These types of imperfections are not uncommon, especially on the inside of the frame where you can’t see them. Less common to see them on the outside as they are usually caught in quality control inspections. While they are not ideal, as areas with voids will be somewhat weaker than areas without voids (depending on the size and depth of the void), they are not critical like a crack.
answered 4 hours ago
Rider_XRider_X
24.9k14595
1
Most importantly, the irregularity seen in the image has mostly smooth edges (except where worn/machined for the clamp). A crack will generally have sharp edges. However, that very thin line below the more obvious dent could be a crack. But it's more likely just a less severe indication of the mold seam that created the dents at the top. A closer examination would be needed to see if its edge are rounded or sharp.
– Daniel R Hicks
3 hours ago
add a comment |
Doesn’t look like a crack, looks more like a surface void that formed during the resin injection molding. These types of imperfections are not uncommon, especially on the inside of the frame where you can’t see them. Less common to see them on the outside as they are usually caught in quality control inspections. While they are not ideal, as areas with voids will be somewhat weaker than areas without voids (depending on the size and depth of the void), they are not critical like a crack.
answered 4 hours ago
Rider_XRider_X
24.9k14595
Doesn’t look like a crack, looks more like a surface void that formed during the resin injection molding. These types of imperfections are not uncommon, especially on the inside of the frame where you can’t see them. Less common to see them on the outside as they are usually caught in quality control inspections. While they are not ideal, as areas with voids will be somewhat weaker than areas without voids (depending on the size and depth of the void), they are not critical like a crack.
answered 4 hours ago
Rider_XRider_X
24.9k14595
edited 3 hours ago
answered 4 hours ago
Rider_XRider_X
24.9k14595
answered 4 hours ago
Rider_XRider_X
24.9k14595
answered 4 hours ago
Rider_XRider_X
24.9k14595
24.9k14595
1
Most importantly, the irregularity seen in the image has mostly smooth edges (except where worn/machined for the clamp). A crack will generally have sharp edges. However, that very thin line below the more obvious dent could be a crack. But it's more likely just a less severe indication of the mold seam that created the dents at the top. A closer examination would be needed to see if its edge are rounded or sharp.
– Daniel R Hicks
3 hours ago
add a comment |
1
Most importantly, the irregularity seen in the image has mostly smooth edges (except where worn/machined for the clamp). A crack will generally have sharp edges. However, that very thin line below the more obvious dent could be a crack. But it's more likely just a less severe indication of the mold seam that created the dents at the top. A closer examination would be needed to see if its edge are rounded or sharp.
– Daniel R Hicks
3 hours ago
1
1
Most importantly, the irregularity seen in the image has mostly smooth edges (except where worn/machined for the clamp). A crack will generally have sharp edges. However, that very thin line below the more obvious dent could be a crack. But it's more likely just a less severe indication of the mold seam that created the dents at the top. A closer examination would be needed to see if its edge are rounded or sharp.
– Daniel R Hicks
3 hours ago
Most importantly, the irregularity seen in the image has mostly smooth edges (except where worn/machined for the clamp). A crack will generally have sharp edges. However, that very thin line below the more obvious dent could be a crack. But it's more likely just a less severe indication of the mold seam that created the dents at the top. A closer examination would be needed to see if its edge are rounded or sharp.
– Daniel R Hicks
3 hours ago
add a comment |
Thanks for contributing an answer to Bicycles Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fbicycles.stackexchange.com%2fquestions%2f60186%2fis-this-a-crack-on-the-carbon-frame%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Take this same photo monthly, and compare it over time. If the line changes and grows in width or thickness then its a crack. If not, it isn't.
– Criggie♦
2 hours ago